http://www.bing.com:80/search?q=Smart+TVSearch resultshttp://www.bing.com:80/s/a/rsslogo.gifhttp://www.bing.com:80/search?q=Smart+TVCopyright © 2026 Microsoft. All rights reserved. These XML results may not be used, reproduced or transmitted in any manner or for any purpose other than rendering Bing results within an RSS aggregator for your personal, non-commercial use. Any other use of these results requires express written permission from Microsoft Corporation. By accessing this web page or using these results in any manner whatsoever, you agree to be bound by the foregoing restrictions.https://www.eng-tips.com/threads/amp-readings.87604/here's the story, the plumbers in the building maint. department say there is a clog in the 8inch pipe down the line from the discharge.well when the pump runs,after about 30mins, it heats up and the amp reading are 6.4amps on each phase. the nameplate on the motor is 9.5amps on a 480volt connection. question, if there was a clog on the pipe wouldn't the amps be higher than 9.5amp and than ...Wed, 22 Apr 2026 12:24:00 GMThttps://www.eng-tips.com/forums/337/faqs/28852024 National Design Specification (NDS) for Wood Construction (view only), AWC website. 2024 NDS supplement (view only), AWC website. 2021 Special Design Provisions for Wind and Seismic (view only), AWC website. (Be aware there is a 0.92 reduction applicable to shear walls with 10d nails and holdowns on the inside face of the shear wall that has been added. See 2021 Special Design Provisions ...Wed, 22 Apr 2026 00:21:00 GMThttps://www.eng-tips.com/threads/fasteners-on-curved-surface.177666/Working on a sheet metal assembly where I need to put some screws through the side wall of a circular cylinder. But SolidWorks refuses to properly mate the screws to the holes in the assembly. Can't add any relations to get the screws properly positioned relative to the holes, and Smart...Sun, 19 Apr 2026 00:10:00 GMThttps://www.eng-tips.com/threads/how-to-dimension-in-a-detail-view.282669/Hi everyone, Can anyone help me dimension a feature when i use a ballooned detail view. I would like to import diameter dimension's onto a flange I created a detail view but have not been able to figure. Thank youTue, 14 Apr 2026 16:08:00 GMThttps://www.eng-tips.com/threads/nx-journal-and-block-ui-styler-combination.424032/Hi all, with the help of ufsure, I've learnt to combined a journal code with the UI Block Styler so as to retrieve the input co-ordinate values from the block dialog into my journal code. The code was changed from NXOpen.Point3d originPoint1 = new NXOpen.Point3d(0.0, 0.0, 0.0)...Tue, 21 Apr 2026 19:28:00 GMThttps://www.eng-tips.com/threads/any-options-other-than-limit-switches.260375/I highly recommend simplifying the design as much as you can. I worked on another design that used limit switches to lower a plasma tv over the windshield in a motor home. If the limit switches failed the electric actuator burned up and if the little old lady got between the TV and windshield it pushed her out onto the ground, apparently a bad ...Fri, 17 Apr 2026 06:04:00 GMThttps://www.eng-tips.com/threads/need-a-laymans-explanation-of-asce-7-wind-maps.570013/a) What you hear on TV is based on whatever equipment measured it at some point. You have no idea if that speed is sustained. You don't know if localized areas of the storm have higher or lower speeds. It's just to give you (the viewer) a sense of how powerful those hurricane winds are. b) The Wind maps in ASCE-7 are based on a "3 second gust ...Mon, 20 Apr 2026 08:45:00 GMThttps://www.eng-tips.com/threads/looking-for-an-autocad-alternative-that-handles-flatshot-effectively.381341/Two years ago, my previous employer was looking for a cheaper alternative to AutoCAD and came across with this software which was almost identical to AutoCAD. The software is called ZWCAD, you may be aware of it, or heard about it. It really is very identical to autocad, as the agent selling had given us demo to play with. So maybe it has flatshot function also.Fri, 17 Apr 2026 15:15:00 GMT